Follow

XDJ-R1 - WiFi Setup Instructions

The following instructions are to configure the wireless access point settings for your XDJ-R1:

  • Turn on the XDJ-R1
  • Press and hold the UTILITY button to enter the utility mode
  • Turn the knob to show WLAN SETTING, push the knob to select it
  • Turn the knob to show RESET TO DEFAULTS, push the knob to select it
  • Turn the knob to show YES, and push the knob to select it
  • The screen will show DEFAULT
  • Push the knob to return to the previous menu
  • Press and hold the POWER to turn off the XDJ-R1
  • Unplug the power cable and leave it unplugged for 30 seconds
  • Re-connect the power cable and turn on the XDJ-R1
  • Press and hold the UTILITY button to enter the utility mode
  • Turn the knob to show WLAN SETTING, push the knob to select it
  • MODE will appear in the display, push the knob to select it
  • Turn the knob to show WLAN ENABLE and push the knob
  • If prompted to APPLY CHANGE?, turn to show YES and push the knob to accept
  • Turn the knob to show NETWORK SETTING, and push the knob to select it
  • Choose an SSID name for your WiFi network using the knob to change characters, press the BACK button to erase characters, push the knob when you are done
  • You are next shown SECURITY, turn the knob to show OPEN and push the knob
  • If prompted to APPLY CHANGE?, turn to show YES and push the knob to accept
  • Turn the knob to show OTHERS, and push the knob to select it
  • CHANNEL NO. will appear in the display, push the knob to select it
  • Turn the knob to show AUTO, push the knob to select it
  • If prompted to APPLY CHANGE?, turn to show YES and push the knob to accept
  • Turn the knob to show DHCP SERVER, and push the knob to select it
  • Turn the knob to show ENABLE, and push the knob to select it
  • If prompted to APPLY CHANGE?, turn to show YES and push the knob to accept
  • Push the BACK button
  • Turn the knob to show WLAN INFO, and push the knob to select it
  • Turn the knob to show IP ADDRESS, and push the knob to select it
  • Your IP address should show as something similar to 192.168.2.3 (the default value), turn the knob to scroll to the right to show the full number
  • Press the INFO button to exit the Utility mode

You should now be ready to connect a device to your XDJ-R1. If you have chosen an SSID previously used by a device, be sure to use the FORGET NETWORK function of your device to remove any previously stored credentials.

After you have confirmed the ability to connect to your XDJ-R1, be sure to set-up some network security:

  • Press and hold the UTILITY button to enter the utility mode
  • Turn the knob to show WLAN SETTING, push the knob to select it
  • Turn the knob to show NETWORK SETTING, and push the knob to select it
  • Push the knob to keep your existing SSID
  • You are next shown SECURITY, turn the knob to show WEP128 and push the knob
  • You are next shown PASSWORD, you can keep the default password or change it to your own - scroll using the knob to show the end of the password or press the BACK button to erase characters
  • If creating your own password, you may use any characters available, but a minimum of 13 characters is required for a WEP128 password, push the knob to accept the password
  • If prompted to APPLY CHANGE?, turn to show YES and push the knob to accept
  • Press the INFO button to exit the Utility mode

Before connecting with your device again, be sure to use the FORGET NETWORK function to remove any previously stored credentials as your XDJ-R1 wireless network now requires a password with WEP128 security as it did not before.

Once your device has connected, showing the information for that network should reveal the following information:

  • IP Address: 192.168.2.x
  • Subnet Mask: 255.255.255.0
  • Router: 192.168.2.3
  • DNS: 0.0.0.0

You will now be able to connect to your XDJ-R1 with the remotebox application.

If you require further assistance, please post a topic in the XDJ section of the forums.

Was this article helpful?
0 out of 2 found this helpful

Comments