Omnisistem - Stinger 1
- Omnisistem
- Stinger 1
- Aerial
- https://omnisistem.com/
- https://www.manualslib.com/manual/2009690/Omnisistem-Stinger-1-Series.html
- To set the DMX address or Stand-alone Personality on your New Stinger
Stand-alone Sound Active Mode
1. The unit is pre-set in sound-active mode. Verify the correct voltage setting and plug in to power.
Please No Dimmers or Relay Packs.
2. Switch the unit on.
3. The unit will auto-run patterns to audio in the room. There is no duty cycle.
4. The setting for sound-active stand-alone operation is listed below:
909
DMX-512 Mode
1. Make certain the voltage select switch is in the proper position for your country’s voltage.
2. Plug the unit in to power and switch into the “On” position.
3. Press "Enter" to enter the address setting mode.
The first digit in line will begin flashing.
4. Press "Select" The selected digit will be flashing
5. Press either "U" for up or "D" for down to change the value of the selected digit (from 0 through 9).
6. Press "Enter" to save the new address.
7. Connect the DMX interface cable from unit to DMX-512 console.
8. On your DMX console, move the channel 1 fader up to a value of 15 and adjust the channel 3 fader to select
pattern as a quick test for communication.
9. After address has been changes, turn unit off and on again for new address to take affect.
10. You’re all set. Enjoy.
DMX Controls
The NEW Stinger Series offers up to 7 Channels of DMX-512 control. If you have purchased a single color laser
some of these values and channels may not be used. This is controlled at the PCB level of your product therefore
adjusting those faders will not damage the unit nor will it have any effect.
Ch.1 Beam On-Off / Color Select
Ch.2 Color Mode - Not Available on Single Color Models
Ch.3 Pattern Select
Ch.4 Pattern Speed
Ch.5 Not Available on Single Color Models
Ch.6 Not Available on Single Color Models
Ch.7 "Y" Axis Offset (Up and Down)
Channel 1 Beam Control
00-10 Beam Off
11-50 Beam On (Green/Red/Blue Stingers)
51-90 Green/Blue Only
91-130 Red Only
131-170 Beam On (Green/Red Stingers)
171-255 Beam Off (Slow)
Channel 2 Color Control - Not Used on Single Color Models
SETTING THE MODE VIA THE LED MENU
OPERATION
4
Channel 3 Pattern Control
00-08 Beam Off
09-17 Beam Chase #1
18-26 Split Sky Horizontal
27-35 Split Sky Vertical
36-44 Flat Beam Fan
45-53 Rotating Beam Fan
54-62 Dual Counter Rotating Beam Fans
63-71 Tight Square Cone (rotates)
72-80 Dual Flat Beam Scan
81-89 Dual Sky (opens then closes)
90-98 Bouncing Beam Fan
99-107 Box Tunnel #1 (Closes "X" Axis Only)
108-115 Quad Tunnel (rotates)
116-125 Triangle Tunnel (rotates)
126-134 V-Sky
135-143 Dual Diagonal Fans #1
144-152 Dual Diagonal Fans #2
153-161 Box Tunnel #2 (Closes on "X" and "Y")
162-170 Quad Tunnel (fixed)
171-179 Counter Rotating Fans
180-188 Dual Beam Cones (tight)
189-197 Single Rotating Beam Fan
198-206 Dual Beam Fans (tight)
207-215 Dual Beam Fans (one flat, one rotates)
216-224 Beam Cone
225-233 Dual Rotating Square Cones
234-242 Beam Chase #2 (adjust channel 4 for effect)
243-255 Beam Chase #3 (adjust channel 4 for effect)
Channel 4 Pattern Speed
00-230 Fastest to Slowest
231-255 Freeze Frame (Pattern Hold)
Channel 5 X Axis amplitude (crunches down image, then inverts it top to bottom)
Channel 6 Y Axis amplitude (crunches down image, then inverts it side to side)
Channel 7 Y Axis Offset (allows user to raise and lower scan area)
00-13 Normal setting
14-53 Lowers "Y" Axis Offset
54-127 Raises "Y" Axis Offset
128-255 Snap to Center
There are several options available under DMX control. Below is a brief overview.
PATTERN
28 Base Patterns to include all your favorites like Liquid Sky, Tunnels, Fans, Beam Chases and much
more.
PATTERN SPEED and HOLD
Find a pattern you like and then adjust the speed to your liking; you can also “Freeze” the pattern by
simply pushing the channel 4 fader all the way up.
Y AXIS OFFSET
This feature enables you to raise or lower the position of your effect on cue.
PRIMARY COLOR CONTROL
Take control of the Green and Red to turn them on and off manually via DMX.
(Allows users with different models of Stinger to control individual COLORS)
Effects and Color Control
La publicación no admite más comentarios.
1 comentario
