Major Bug in Toraiz sp-16 sequencer

Not on mine.  I can run both an external sequence on my SH-01A alongside an SP-16 sequence (ch 1) - the SH-01A is set to polyphonic, so it plays both at the same time - and have another sequence playing from the SP-16 into a Bass Station II (ch 2) and the timing is solid.  The internal sequence in the SH-01A is set to 100 steps, so it does not follow the same 16 steps as the SP-16, but both are perfectly in sync with each other.

Does anything in particular trigger this behavior?  

i have two scene this issue  also i feel we need independent track control for rolls whie being able to mute other pads

I can only log in to UK website, not USA so they will not see this comment

I had no problems like this when I was using a laptop and a DAW so I am certain it is pioneer. Just go ahead and create a two bar sequence to sequence an external synth, create notes in the first bar with a note on the last step (1 step length) and leave the next bar blank and the note should repeat endlessly.

Sorry, man, but I still don't have that problem.  I tried to set the note length longer, but it didn't do it then, either.  

I did as you said: set a 2-measure pattern with notes only in the first measure (and the last note on step 16, plus I tried notes on 13, 14, and 15) and the note doesn't carry on for me.  

Not sure what's up with yours, but I cannot repeat what you're doing.   If you think of something else to try, I'd be happy to.  

Thanks for all the replies.

I have just created an intro to a track - scene 1 pattern 2 is the 1st four bars, then link that up in the arranger to scene 1 pattern 3 for the next four bars of (differing) melody then go to scene 1 pattern 1 for the track itself. I've removed all triggers for the instrument in question scene 1 pattern 1 but the melody (last note) repeats endlessly. I made the demo's on a DAW and in most instances I am perfectly replicating what I created there on the Toraiz and had no problems (on the DAW).

Having said that whe I tried the previous example I gave earlier...

(create a two bar sequence to sequence an external synth, create notes in the first bar with a note on the last step (1 step length) and leave the next bar blank and the note should repeat endlessly)

I was not able to re-create the flaw (but had previously)

So, the problem seems to come and go and I cannot isolate the  conditions under which the results vary.

Re: MIDI capture, I tried to capture a 4 note bassline but was only able to record 2 notes but persisted until I recorded three notes from the bassline (which was played back off the bass machine's sequencer, not played manually).

Does anyone else experience these kind of problems?

Even worse, I have discovered that not only does one note interfere with another on the same track but there is a knock on effect onto other tracks. Track 5 & 6's notes repeat endlessly (going from scene 1 pattern 3) into a blank track (scene 1 pattern 1), unless I shorten the notes so they finish before the end of the bar) but they also interfere with my drum track (4) unless I offset the notes on track 5 & 6 so they don't all trigger at the same time.

Dunno what to tell you!  I haven’t had the same problems, but sympathize with your frustration.

Are there certain samples and external synths that you’re using when things go awry or does it happen with any sample/external combination?

No, I have a complete set of Roland Aira's which I use for aevery track and I had no problems with the same tracks on my DAW.

Here's another one, when switching scenes I send MIDI to my mixer (Aira MX-1) but the signal is 1 step (1/4 note slow) so it sounds poor - I will have to mute 3 channels manually on my mixer because the Toraiz's timing is latent.